---
title: "Allard Krings (@allard) | Hashnode"
description: "Allard Krings (@allard) writes on Hashnode. Read their latest articles and follow their work."
url: "https://hashnode.com/@allard"
---

@allard

# Allard Krings

@allard · Joined December 2023

## Comments

[Allard Krings that is micro-SD off course!](https://hashnode.com/posts/installing-ubuntu-server-starfive-visionfive-2-riscv/6562877207549d040bf4b76b/comment/65667ed2cda818ef519cefd8#reply-657ca26df7ee9350b5c95e78)

Reply · Article · Dec 15, 2023 · [Installing Ubuntu Server on the StarFive VisionFive 2](https://hashnode.com/posts/installing-ubuntu-server-starfive-visionfive-2-riscv/6562877207549d040bf4b76b)

[Adam Hartley hi Adam, thanks a lot for your help! I was indeed able to install ubuntu on the NVME-drive. However fter rebooting the sbc had a reallocation-error. After some searching on internet I found a tip replacing the firmware that Starfive provides by the one from Ubuntu. This is obligatory if you have the 1.2a revision! Now ubuntu boots fine from yhe NVME-drive, no SSD needed!](https://hashnode.com/posts/installing-ubuntu-server-starfive-visionfive-2-riscv/6562877207549d040bf4b76b/comment/65667ed2cda818ef519cefd8#reply-657c98a2f7ee9350b5c91126)

Reply · Article · Dec 15, 2023 · [Installing Ubuntu Server on the StarFive VisionFive 2](https://hashnode.com/posts/installing-ubuntu-server-starfive-visionfive-2-riscv/6562877207549d040bf4b76b)

[Adam Hartley Helo , i am not even getting to the point where I can replace the DTB. This is my ouput: Model: StarFive VisionFive V2 Net: eth0: ethernet@16030000, eth1: ethernet@16040000 Hit any key to stop autoboot: 0 StarFive # pci enum starfive\_pcie pcie@2B000000: Port link up. starfive\_pcie pcie@2B000000: Starfive PCIe bus probed. PCI: Failed autoconfig bar 10 starfive\_pcie pcie@2C000000: Port link up. starfive\_pcie pcie@2C000000: Starfive PCIe bus probed. PCI: Failed autoconfig bar 10 StarFive # nvme scan StarFive # load mmc 0:1 $fdt\_addr\_r dtb/starfive/jh7110-starfive-visionfive-2-v1.2a.dtb Card did not respond to voltage select! : -110 Couldn't find partition mmc 0:1 Can't set block device StarFive #](https://hashnode.com/posts/installing-ubuntu-server-starfive-visionfive-2-riscv/6562877207549d040bf4b76b/comment/65667ed2cda818ef519cefd8#reply-6576eeb124c0bd2319fef372)

Reply · Article · Dec 11, 2023 · [Installing Ubuntu Server on the StarFive VisionFive 2](https://hashnode.com/posts/installing-ubuntu-server-starfive-visionfive-2-riscv/6562877207549d040bf4b76b)

[Adam Hartley Hi, I have the 1.2A version of the board with an NVME installed. Following the tutorial does not work. Is it possible at all to install ubuntu on that? Even on a simple SD card it does not boot. If so , what step should I do differently from your tutorial?](https://hashnode.com/posts/installing-ubuntu-server-starfive-visionfive-2-riscv/6562877207549d040bf4b76b/comment/65667ed2cda818ef519cefd8#reply-6575770532862421fba1bf20)

Reply · Article · Dec 10, 2023 · [Installing Ubuntu Server on the StarFive VisionFive 2](https://hashnode.com/posts/installing-ubuntu-server-starfive-visionfive-2-riscv/6562877207549d040bf4b76b)